Jump to content
Sign in to follow this  
Jim Katen

Unknown Object

Recommended Posts

This device is screwed onto a baseboard in the living room of a 1911 craftsman bungalow in SE Portland (Westmoreland/Sellwood). A single fabric-covered wire emerges from the baseboard and terminates under one of the knurled screws. The other screw is empty. The wire is not energized and I can't find its other end in the crawlspace below or in the attic above. 

An old radio grounding terminal? Antenna connection point? 

Does anyone recognize it? 

RIMG0068.JPG

RIMG0063.JPG

Share this post


Link to post
Share on other sites

Radio grounding connection or radio antenna are still my prime suspects. The thing is, most old radio grounds & antennas consisted of a simple wire connected directly to the radio. Sometimes they used a radio antenna plug, which I see several times a year. 

This little gadget just seems awfully involved for a simple radio splice point. After seeing Jim Baird's comment, I looked at lots of pictures of telegraph equipment and this thing really looks like part of that equipment. I doubt that the house had a telegraph, but someone might have re-purposed a piece of telegraph equipment as the antenna or ground connection for their radio. 

 

 

Share this post


Link to post
Share on other sites

A telegraph office would be possible if the location seems right.

If it is just a residence, it is probably as mentioned by Rob, nothing more than an antenna connector for the big console radio. They didn't start having internal loop antennas until the early 30's. And for short wave, they'd add a long wire antenna, maybe strung up in the attic.

 

Edited by John Kogel

Share this post


Link to post
Share on other sites

I've been on a mission and I think I have found the manufacture source of the "binding post".

Link will take you to the website for the catalog from Bunnell Telegraphic and Electrical catalog with a suggested published date of 1901.

Image is from the page relating to the "binding posts" the seem to be quite similar to Katen's image.

http://www.telegraph-history.org/bunnell-tel-elec-catalog/index.html 

 

Bunnell-binding-posts.JPG

  • Like 2

Share this post


Link to post
Share on other sites

Thanks Nolan. 

It looks very similar to "Style A" which would have set someone back $0.17. 

Clearly, it's a repurposed piece of telegraph equipment. 

Thanks again for the leg work. 

Share this post


Link to post
Share on other sites

Telegraph 'binding post' in a house.. .hmmm... smells like a HAM    :)  I should have figured that out...    (Uncle-K1AWP, brother-N1MX)     Beep beep ba deep... Or I should say "73'!! 

Meanwhile... not 1 foot away from my seat, there is this:    

IMG_1037.JPG

Share this post


Link to post
Share on other sites

Thats a speed telegraph unit.  Instead of doing dits and dots up and down, these units allow the operator to use a side to side motion to send much faster code.  

Share this post


Link to post
Share on other sites

I don't use it... but I 'know' Morse code ... it was 'absorbed' since age 12..     Being a musician also helps to learn/understand it (and vice versa by the way!)        The key set is a Standard Model Mac Key... Manufactured by Theodore R Mc Elroy   "world's' champion radio telegrapher'..   Boston, Mass, USA  :)

The only time I use 'code' is to rag on my brother (the ham) or talk to him "in code' secretly or to see if the code used in a movie is correct or not.. (surprising how often it's correct.. ) 

Share this post


Link to post
Share on other sites

Nice video... that guy's little keyer-rig is not heavy enough...

The one I have is a cast-iron monster... as my Italian grandmother would have said.. "She no move.. "   ... it's 100% mechanical...

 

  • Like 1

Share this post


Link to post
Share on other sites

...my grandfather worked for Western Union for 50 yrs.  When he retired they gave him a gold watch and a salt water fishing rod, but he never got to wet that hook.  He collapsed while shaving at the bathroom mirror a cpl of months after he retired.

Share this post


Link to post
Share on other sites
On 4/19/2018 at 7:52 AM, Rob Amaral said:

Nice video... that guy's little keyer-rig is not heavy enough...

The one I have is a cast-iron monster... as my Italian grandmother would have said.. "She no move.. "   ... it's 100% mechanical...

 

When I was a code guy for the usaf we made these speed keys with hack saw blades which had a really great flexibility.  Yes, the one in the vid is wimpy.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×